Canada

Used Machinery

  • Used Machinery Community Bulletin Board


    UNLESS NOTED OTHERWISE, the following listings are a community bulletin board for MiTek customers selling their current machinery in order to purchase new, state-of-the-art MiTek® machinery.  To purchase or obtain more information about the machinery on this page, contact the seller directly.

    Please email usedmachinery@mitek.ca to request that an item be added to this bulletin board.

    Please send us an email when the equipment is sold. Thanks!. 


  • 4 Blade plus router Clary Component Saw

    From late 70's early 80's
    Cuts from 3' to 20' lengths
    Used within the last three years
    Still in storage
    Asking Price: Accepting Offers

    For more information contact:
    Derrick Garland
    Jag Roof Trusses
    Email: info@jagrooftrusses.com
    Office: 709-596-5093

     JagRootTruss-ClarySaw-Image-T

  • SpeedCut jack Rafter Saw

    Model #: SB2
    Serial #: X0229
    Includes 16' and 10' conveyors. Currently using, in good working condition. Available September 2015 or November 2015.
    $1,000.00 CDN

    For more information contact:

    John Sochatzy
    Email: john.sochatzy@pallisertruss.ca
    Office: 403-946-4642
    Cell: 403-835-2817
    Palliser-JackRafterSaw-Image

  • 2007 Triad Wall Panel Saw

    Used for less than 1 year (less than 500 operating hours on saw) and then stored. Able to cut and mark wall plates. Cuts 2x4 to 2x8 plates at 90 degrees or miters them up to + 45 degrees. Servo controlled automated feed and blade angulation. Includes touch-screen-control console, a 10hp, 3 phase saw motor, & an 18" saw blade.

    Manufacture website: http://www.triadruvo.com/wallpanel/platesaw.htm

    Price: $16,000.00 CDN O.B.O

    For more information contact:
    Earl Kellner
    Tim-Br-Fab
    Tel: 204-888-7663
    email: ekellner@timbrfab.com  

    Tim-Br-Fab-Triad_WallPanelSaw-Image

  • Clary Saw

    Model Clary Craftmaster
    Serial # 308 269
    Older model 4 blade Component saw
    Includes waste conveyor
    240 volt, 3 phase
    Cuts lengths up to 18'
    Operational up to August 2012 at which point it was replaced with newer model

    No reasonable offer refused

    For more information contact:

    Dana Doherty
    519-357-2606
    dana@royalhomes.com

    IMG_0092



  • Idaco 4 blade Component Saw

    Model: Componamatic
    Serial #: 3843
    Includes waste conveyor, 4 blades with spares, dado head (3.5” wide by 1.5” deep, currently set at ¾” deep). Added light for adjustment of angles. Adjusts from lumber on flat to lumber on edge up to 2x6 lumber. Cuts up to 24’ length with square cuts and 22’ length with double cuts on each end.

     **No reasonable offer refused**

    For more information contact:

    George Carriere
    Tel: (204) 638-9601
    Email: timbrfab@mts.net

     

    Tim-Br-Fab-IdacoSaw Image


  • Steel Table

    14' x 50' Steel Table with Rollers

    For more information contact:

    Toiturex Inc.
    Gaetan Gauthier or Claude Latulippe
    (418) 343-3315

    Toiturex-SteelTable Image



  • 1997 Easy Set 1000

    - 5 motorized angulated cutting heads with air brakes
    - Full scrap system
    - Motorized vertical adjustment on overhead powered hold-downs
    - Controls and digital readouts from moveable carriage operator station
    - SO electrical cables renewed in 2004, scrap belts, lumber conveyor

    For more information contact:

    Jerry or Marya Kielstra
    1-780-693-2250

    Edson-1997EasySet1000 Image


  • Clary Floor Truss Gantry

    - 600v, 3-phase
    - 6'x36' table
    - End eject
    - Includes table hardware & floor tracks (bolted)
    - Good working order 

    For more information contact:
    Toiturex Inc.
    Gaetan Gauthier or Clause Latulippe
    418-343-3315 

    Toiturex-Clary_Floor Image

  • Truss Table

    Table:
    Length = 593 ‘’
    Width = 162’’
    Height = 27’’

    Roller:
    Width = 60’’
    Length = 199’’

    Finish Roller:
    Width = 42’’
    Length = 187 ‘’   

    Manufactured by P.H.L., 
    St-Ephrem de Beauce, Qc

    For more information contact:

    Clyvanor Ltée
    Marco Drouin
    MDrouin@clyvanor.com
    (418) 228-7690

    Truss Table - Click here for more pictures


  • Safety Speed Cut Panel Saw w/Milwaukee Saw

    In excellent shape

    $2000.00

    For more information contact:
    Jerry Kielstra at Edson Truss - 780-693-2250